English
Español
Français
Português
BTC
ETH
LTC
BCH
USDT
DOGE
DASH
USDC
XRP
XMR
TRX
BNB
SHIB
SOL
DAI
ZEC
ETC
POL
ADA
XLM
Inner bottom frame with speaker
$22.08
₿ 0.00033
Key specifications
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the housing
- Step 6
- Remove the 2 screws, take off the metal bar, and disconnect the main FPC cable
Specifications
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the housing
- Step 6
- Remove the 2 screws, take off the metal bar, and disconnect the main FPC cable
- Step 7
- Remove the bottom daughterboard
- Step 8
- Remove the microphone and the inner bottom frame
- Step 9
- Place the new inner bottom frame and reinstall the microphone
- Step 10
- Reinstall the bottom daughterboard
- Step 11
- Reinstall the metal bar and secure everything again
- Step 12
- Reinstall the screen display on the housing
- Step 13
- Reinstall the battery
- Step 14
- Reinstall the battery cover
Description
Watch the tutorial on YouTube
Replacement instructions
5 min
Very easy
Required:
A soft surface
– You can use a towel, for example
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opening tool on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opening tool and place one end in the middle under the battery.
Then make a 45-degree motion with the opening tool and lift the battery up.
Carefully loosen all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners on the bottom.
Use just enough force to loosen them.
Use a spudger to carefully loosen the screen.
Work along the edges to release the clips.
Do not remove the screen without loosening everything first.
Remove the 2 screws.
Take off the metal bar after loosening the screws.
Disconnect the main FPC cable from the housing.
Unscrew the board’s fasteners.
Carefully lift the board up.
Flip the board over and place it temporarily at the top of the SHIFTphone.
Use the opening tool to remove the microphone from the inner bottom frame.
Do this by making a 90-degree motion.
Then use the same opening tool to remove the inner bottom frame.
Put the new inner bottom frame back into place.
Make sure everything is properly aligned.
Reinstall the microphone in the correct position in the inner bottom frame.
Put the bottom daughterboard back into place.
Make sure it is properly seated.
Tighten the board securely.
Put the main FPC cable back in place.
Reposition the metal bar correctly.
Tighten the two screws again.
Carefully place the screen display back onto the housing.
Press the screen firmly along the edges.
Check that the screen is securely attached everywhere.
Put the SHIFTphone battery back in place.
Insert it correctly into the SHIFTphone.
With the SHIFT logo facing up and the + and – in the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone in the correct orientation.
Press firmly at 8 points until the battery cover is securely attached.
Replacement instructions
5 min
Very easy
Required:
A soft surface
– You can use a towel, for example
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opening tool on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opening tool and place one end in the middle under the battery.
Then make a 45-degree motion with the opening tool and lift the battery up.
Carefully loosen all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners on the bottom.
Use just enough force to loosen them.
Use a spudger to carefully loosen the screen.
Work along the edges to release the clips.
Do not remove the screen without loosening everything first.
Remove the 2 screws.
Take off the metal bar after loosening the screws.
Disconnect the main FPC cable from the housing.
Unscrew the board’s fasteners.
Carefully lift the board up.
Flip the board over and place it temporarily at the top of the SHIFTphone.
Use the opening tool to remove the microphone from the inner bottom frame.
Do this by making a 90-degree motion.
Then use the same opening tool to remove the inner bottom frame.
Put the new inner bottom frame back into place.
Make sure everything is properly aligned.
Reinstall the microphone in the correct position in the inner bottom frame.
Put the bottom daughterboard back into place.
Make sure it is properly seated.
Tighten the board securely.
Put the main FPC cable back in place.
Reposition the metal bar correctly.
Tighten the two screws again.
Carefully place the screen display back onto the housing.
Press the screen firmly along the edges.
Check that the screen is securely attached everywhere.
Put the SHIFTphone battery back in place.
Insert it correctly into the SHIFTphone.
With the SHIFT logo facing up and the + and – in the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone in the correct orientation.
Press firmly at 8 points until the battery cover is securely attached.
More from NovaCustom
All products
$22.08
₿ 0.00033
