Intel BE200 WiFi 7 card, up to 6 GHz 802.11be + BT 5.4

YouTube tutorial – V54 SeriesYouTube tutorial – V56 SeriesYoutube tutorial – NUC Box

Replacement instructions for laptops
You will find the replacement instructions for the NUC Box further down this page.

6 min
Easy

Requirements:

A soft underground
– You could use a towel
A container to put the screws in
– Make sure you don’t lose the screws
Screwdriver
Spudger (or a similar plastic tool)

Put the laptop upside down on a soft underground.

This is needed to prevent scratches on the laptop’s screen lid. Then, remove all the screws with the screwdriver.

Take the spudger and put it between the bottom case and the hinge.

Gently apply pressure to the hinge. Do this on both sides. You can then carefully remove the bottom case entirely.

You can now replace the WiFi module.

To remove the existing WiFi module, remove its screw. The module will pop out and can be taken out. Remove the antenna cables from the module with care.

To install your WiFi module, insert it with an angle of about 30°. Reattach the antenna cables, but please don’t use excessive force since the antennas and the antenna plugs are fragile.

Make sure that the module is pushed correctly in its slot. Once it’s in, push the module down at the outside and install the belonging screw.

Important:
The antenna cables and the plugs at the module are fragile. Make sure you push the antennas in place with proper force – never use excessive force.

The white WiFi antenna plug shuold be attached to MAIN, while the transparent WiFi antenna plug should be attached to AUX.

Install the bottom case by placing it back in the right position.

Gently press the part on all sides.

Make sure that the bottom case fits snugly everywhere.

Use the screwdriver to install the screws back in place. In case of the V54 Series: play close attention to the two screws at the hinges: these are bigger than the other screws.

This was the final step, you are ready to use your laptop again.

Well done!

Replacement Instructions for NUC Box

5 min
Very easy

Requirements:

A soft surface
– You can use a towel, for example
A small container to put the screws in
– Make sure you do not lose any screws
Screwdriver

Place the NUC Box upside down on a soft surface.

This prevents scratches on the NUC Box.

Then remove all screws using the screwdriver.

Step 2: Remove the bottom cover
Pick up the NUC Box and carefully turn it over.

Next, grip the top cover at all corners.

Lift it off from the bottom.

You can now replace the WiFi module.

To remove the existing WiFi module, remove the screw. The module will pop up and can be removed. Carefully disconnect the antenna cables from the module.

To install your new WiFi module, insert it at an angle of approximately 30°. Reattach the antenna cables, but do not use excessive force, as the antennas and antenna connectors are fragile.

Make sure the module is properly seated in its slot. Once it is in place, press the outer edge of the module down and reinstall the corresponding screw.

Important:
The antenna cables and the connectors on the module are fragile. Make sure you attach the antennas using the correct amount of force – never use excessive force.

The white WiFi antenna connector must be connected to MAIN, while the transparent WiFi antenna connector must be connected to AUX.

Step 4: Reinstall the bottom cover
Place the bottom cover of the NUC Box back in the correct position.

Make sure the arrow labeled front is actually pointing towards the front.

You can verify this by slightly lifting the NUC Box at the front.

Step 5: Reinstall the screws
Use the screwdriver to tighten the screws back into place. Note: do not overtighten the screws. Otherwise, it will become very difficult to remove them again in the future if necessary.

The new bottom cover is now installed.

Well done!

×
❮

❯

.image-container {
}

.zoom-image, .aligncenter.size-large {
}

.zoom-image:hover {
}

.zoomoverlay {
display: none;
position: fixed;
transition: opacity 0.3s ease !important; /* Fade effect */
}

.zoomoverlay.show {
display: flex; /* Make it a flex container when shown */
opacity: 1; /* Fully visible */
}

.zoomoverlay img {
}

#close {
position: absolute;
top: 20px;
}
.nav-btn {
position: absolute;
top: 50%;
transform: translateY(-50%);
background-color: rgba(255, 255, 255, 0.3);
font-size: 24px;
transition: background-color 0.3s ease;
z-index: 11;
}

.nav-btn:hover {
background-color: rgba(255, 255, 255, 0.6);
}

.prev-btn {
left: 20px;
}

.next-btn {
right: 20px;
}

document.addEventListener('DOMContentLoaded', function() {
const parentDiv = document.getElementsByClassName('repair-badges')[0].parentElement;
const images = parentDiv.querySelectorAll('img[src$=".png"]');
let imageArray = []; // Array om alle afbeeldingen op te slaan
let currentImageIndex = 0; // Huidige afbeelding bijhouden

images.forEach((image, index) => {
// Check if the image is inside an anchor tag and skip if it is
if (image.parentElement.tagName.toLowerCase() === 'a') {
return; // Skip this image
}

image.classList.add('zoom-image'); // Add the zoom class
imageArray.push(image); // Voeg toe aan array

image.addEventListener('click', function() {
currentImageIndex = imageArray.indexOf(this); // Stel huidige index in
showImage(this.src);
});
});

function showImage(src) {
const overlay = document.getElementById('zoomoverlay');
const enlargedImage = document.getElementById('enlargedImage');
let originalSrc = src;

// Check for the '300x' in the filename
if (originalSrc.includes('300x')) {
const lastDashIndex = originalSrc.lastIndexOf('-');
if (lastDashIndex !== -1) {
originalSrc = originalSrc.substring(0, lastDashIndex) + '.png';
}
}

enlargedImage.src = originalSrc;

// Show the overlay with fade-in
overlay.style.display = 'flex';
setTimeout(() => {
overlay.classList.add('show');
}, 10);
}

function navigateImage(direction) {
if (imageArray.length === 0) return;

if (direction === 'next') {
currentImageIndex = (currentImageIndex + 1) % imageArray.length;
} else if (direction === 'prev') {
currentImageIndex = (currentImageIndex - 1 + imageArray.length) % imageArray.length;
}

showImage(imageArray[currentImageIndex].src);
}

document.getElementById('close').addEventListener('click', closeOverlay);
document.getElementById('prevBtn').addEventListener('click', () => navigateImage('prev'));
document.getElementById('nextBtn').addEventListener('click', () => navigateImage('next'));

// Close overlay if clicking elsewhere on the overlay
document.getElementById('zoomoverlay').addEventListener('click', function(e) {
if (e.target !== this && !e.target.classList.contains('nav-btn')) return;
closeOverlay();
});

// Keyboard navigation
document.addEventListener('keydown', function(event) {
const overlay = document.getElementById('zoomoverlay');
if (!overlay.classList.contains('show')) return; // Alleen actief als modal zichtbaar is

if (event.key === 'Escape') {
closeOverlay();
} else if (event.key === 'ArrowRight') {
navigateImage('next');
} else if (event.key === 'ArrowLeft') {
navigateImage('prev');
}
});

function closeOverlay() {
const overlay = document.getElementById('zoomoverlay');
overlay.classList.remove('show');

setTimeout(() => {
overlay.style.display = 'none';
}, 300);
}
});