English
Español
Français
Português
BTC
ETH
LTC
BCH
USDT
DOGE
DASH
USDC
XRP
XMR
TRX
BNB
SHIB
SOL
DAI
ZEC
ETC
POL
ADA
XLM
Short antenna cable
$9.93
₿ 0.00015
Principales caractéristiques
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the display assembly from the housing
- Step 6
- Remove the 2 screws, remove the metal bracket, and disconnect the main FPC cable
Caractéristiques
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the display assembly from the housing
- Step 6
- Remove the 2 screws, remove the metal bracket, and disconnect the main FPC cable
- Step 7
- Remove the bottom daughterboard
- Step 8
- Remove the 3 cameras
- Step 9
- Disconnect the volume buttons, power button, and front-facing camera
- Step 10
- Completely unscrew the motherboard and carefully turn it over
- Step 11
- Remove the short antenna cable from the motherboard
- Step 12
- Attach the new short antenna cable to the motherboard
- Step 13
- Turn the motherboard over and reinstall it
- Step 14
- Reconnect the volume buttons, power button, and front-facing camera
- Step 15
- Reconnect the main camera and ultra-wide camera
Description
Watch the tutorial on YouTube
Replacement Instructions
5 min
Very easy
Requirements:
A soft surface
– For example, you can use a towel
Spudger
Precision screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Next, remove the battery cover using the opening notch on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the spudger and place one end underneath the center of the battery.
Then make a 45-degree levering motion with the spudger and lift the battery upward.
Carefully loosen all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Apply just enough force to loosen them.
Use a spudger to carefully loosen the display.
Work your way around the edges to release the clips.
Do not remove the display until all clips have been released.
Remove the 2 screws.
Remove the metal bracket after taking out the screws.
Disconnect the main FPC cable from the housing.
Unscrew the board’s mounting screws.
Carefully lift the board.
Gently disconnect the cables.
First, use the spudger to disconnect the front-facing camera.
Then use the spudger to disconnect the main camera and the ultra-wide camera.
Set the main camera and ultra-wide camera aside.
Use the spudger to disconnect the volume button flex cable on the left side. Apply firm but controlled pressure.
Repeat this process for the power button on the right side. Apply firm but controlled pressure.
Completely remove the front-facing camera and set it aside.
Remove all screws securing the motherboard.
Carefully flip the motherboard over using the spudger.
Make sure all cables remain intact and are not damaged.
First, use the spudger to disconnect the connector.
Apply light pressure, but do not use excessive force.
Then completely remove the short antenna cable from the motherboard.
Connect the short antenna cable to the motherboard.
Carefully press it into place using your thumb.
Then route the cable neatly along the edge and reconnect the connector.
Carefully turn the motherboard over and place it back into its correct position.
Make sure no cables are trapped underneath the motherboard.
Then secure the motherboard with its screws.
Reconnect the volume buttons correctly.
Reconnect the power button.
Reinstall the front-facing camera.
Reconnect the main camera in its correct position.
Reconnect the ultra-wide camera in its correct position.
Make sure the main camera is positioned above the ultra-wide camera.
Replacement Instructions
5 min
Very easy
Requirements:
A soft surface
– For example, you can use a towel
Spudger
Precision screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Next, remove the battery cover using the opening notch on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the spudger and place one end underneath the center of the battery.
Then make a 45-degree levering motion with the spudger and lift the battery upward.
Carefully loosen all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Apply just enough force to loosen them.
Use a spudger to carefully loosen the display.
Work your way around the edges to release the clips.
Do not remove the display until all clips have been released.
Remove the 2 screws.
Remove the metal bracket after taking out the screws.
Disconnect the main FPC cable from the housing.
Unscrew the board’s mounting screws.
Carefully lift the board.
Gently disconnect the cables.
First, use the spudger to disconnect the front-facing camera.
Then use the spudger to disconnect the main camera and the ultra-wide camera.
Set the main camera and ultra-wide camera aside.
Use the spudger to disconnect the volume button flex cable on the left side. Apply firm but controlled pressure.
Repeat this process for the power button on the right side. Apply firm but controlled pressure.
Completely remove the front-facing camera and set it aside.
Remove all screws securing the motherboard.
Carefully flip the motherboard over using the spudger.
Make sure all cables remain intact and are not damaged.
First, use the spudger to disconnect the connector.
Apply light pressure, but do not use excessive force.
Then completely remove the short antenna cable from the motherboard.
Connect the short antenna cable to the motherboard.
Carefully press it into place using your thumb.
Then route the cable neatly along the edge and reconnect the connector.
Carefully turn the motherboard over and place it back into its correct position.
Make sure no cables are trapped underneath the motherboard.
Then secure the motherboard with its screws.
Reconnect the volume buttons correctly.
Reconnect the power button.
Reinstall the front-facing camera.
Reconnect the main camera in its correct position.
Reconnect the ultra-wide camera in its correct position.
Make sure the main camera is positioned above the ultra-wide camera.
Autres produits de NovaCustom
Tous les produits
$9.93
₿ 0.00015
