NovaCustom-GOODRAM PX600 250 GB SSD

Features:

YouTube tutorial – V54 SeriesYouTube tutorial – V56 SeriesYouTube tutorial – NUC Box

Replacement Instructions for laptops
You can find the replacement instructions for the NUC Box further below on this page.

6 min
Very easy

Requirements:

A soft surface
– You can use a towel
A small container for the screws
– Make sure you don’t lose the screws
Screwdriver
Spudger (or a similar plastic tool)

Place the laptop upside down on a soft surface.

This is necessary to prevent scratches on the laptop lid.Then remove all screws using the screwdriver.

Take the spudger and place it between the bottom case and the hinge.

Carefully apply pressure to the hinge.You can then carefully remove the bottom case completely.

You can now install or replace the desired SSD storage drive(s).

To remove an SSD, remove the corresponding screw. The module will pop up and can be removed.

To install your new SSD, insert it at an angle of approximately 10–30°, depending on how smoothly the SSD slides in.

Make sure it is properly seated in its slot, but do not use excessive force. Once it is inserted, press the module down on the outer edge and install the corresponding screw.

Important:
Make sure that all thermal pads attached to the NUC Box have been detached. The thermal pads ensure that your SSD stays cool, even under heavy load.

It is essential that they are properly in place to guarantee a long lifespan of your SSD storage drive.

Reinstall the bottom case by placing it back into the correct position.

Gently press on all sides.

Make sure the bottom case fits properly all around.

Use the screwdriver to reinstall the screws. In the case of the V54 Series: pay close attention to the two screws near the hinges, as these are larger than the other screws.

This was the final step; you are now ready to use your laptop again.

Well done!

Replacement Instructions for the NUC Box

5 min
Very easy

Requirements:

A soft surface
– You can use a towel, for example
A small container for the screws
– Make sure you don’t lose any screws
Screwdriver

Place the NUC Box upside down on a soft surface.

This prevents scratches on the NUC Box.

Then remove all screws using the screwdriver.

Pick up the NUC Box and carefully turn it over.

Then grip the top case at all corners.

Lift it off the bottom case.

You can now install or replace the desired SSD storage drive(s).

To remove an SSD, remove the corresponding screw. The module will pop up and can be removed.

To install your new SSD, insert it at an angle of approximately 10–30°, depending on how smoothly the SSD slides in.

Make sure it is properly seated in its slot, but do not use excessive force. Once it is inserted, press the module down on the outer edge and install the corresponding screw.

Important:
Make sure that the protective film has been removed from all thermal pads attached to the top case of the NUC Box. The thermal pads ensure that your SSD stays cool, even under heavy load.

It is essential that they are properly in place to guarantee a long lifespan of your SSD storage drive.

Place the bottom case of the NUC Box in the correct position.

Make sure that the arrow labeled “front” is actually pointing toward the front.

You can check this by slightly lifting the NUC Box at the front.

Step 5: Reinstall the screws
Use the screwdriver to screw the screws back into place. Note: do not overtighten the screws. Overtightening will make it very difficult to remove the screws again if needed in the future.

The new bottom case has now been installed.

Well done!

×
❮

❯

.image-container {
}

.zoom-image, .aligncenter.size-large {
}

.zoom-image:hover {
}

.zoomoverlay {
display: none;
position: fixed;
transition: opacity 0.3s ease !important; /* Fade effect */
}

.zoomoverlay.show {
display: flex; /* Make it a flex container when shown */
opacity: 1; /* Fully visible */
}

.zoomoverlay img {
}

#close {
position: absolute;
top: 20px;
}
.nav-btn {
position: absolute;
top: 50%;
transform: translateY(-50%);
background-color: rgba(255, 255, 255, 0.3);
font-size: 24px;
transition: background-color 0.3s ease;
z-index: 11;
}

.nav-btn:hover {
background-color: rgba(255, 255, 255, 0.6);
}

.prev-btn {
left: 20px;
}

.next-btn {
right: 20px;
}

document.addEventListener('DOMContentLoaded', function() {
const parentDiv = document.getElementsByClassName('repair-badges')[0].parentElement;
const images = parentDiv.querySelectorAll('img[src$=".png"]');
let imageArray = []; // Array om alle afbeeldingen op te slaan
let currentImageIndex = 0; // Huidige afbeelding bijhouden

images.forEach((image, index) => {
// Check if the image is inside an anchor tag and skip if it is
if (image.parentElement.tagName.toLowerCase() === 'a') {
return; // Skip this image
}

image.classList.add('zoom-image'); // Add the zoom class
imageArray.push(image); // Voeg toe aan array

image.addEventListener('click', function() {
currentImageIndex = imageArray.indexOf(this); // Stel huidige index in
showImage(this.src);
});
});

function showImage(src) {
const overlay = document.getElementById('zoomoverlay');
const enlargedImage = document.getElementById('enlargedImage');
let originalSrc = src;

// Check for the '300x' in the filename
if (originalSrc.includes('300x')) {
const lastDashIndex = originalSrc.lastIndexOf('-');
if (lastDashIndex !== -1) {
originalSrc = originalSrc.substring(0, lastDashIndex) + '.png';
}
}

enlargedImage.src = originalSrc;

// Show the overlay with fade-in
overlay.style.display = 'flex';
setTimeout(() => {
overlay.classList.add('show');
}, 10);
}

function navigateImage(direction) {
if (imageArray.length === 0) return;

if (direction === 'next') {
currentImageIndex = (currentImageIndex + 1) % imageArray.length;
} else if (direction === 'prev') {
currentImageIndex = (currentImageIndex - 1 + imageArray.length) % imageArray.length;
}

showImage(imageArray[currentImageIndex].src);
}

document.getElementById('close').addEventListener('click', closeOverlay);
document.getElementById('prevBtn').addEventListener('click', () => navigateImage('prev'));
document.getElementById('nextBtn').addEventListener('click', () => navigateImage('next'));

// Close overlay if clicking elsewhere on the overlay
document.getElementById('zoomoverlay').addEventListener('click', function(e) {
if (e.target !== this && !e.target.classList.contains('nav-btn')) return;
closeOverlay();
});

// Keyboard navigation
document.addEventListener('keydown', function(event) {
const overlay = document.getElementById('zoomoverlay');
if (!overlay.classList.contains('show')) return; // Alleen actief als modal zichtbaar is

if (event.key === 'Escape') {
closeOverlay();
} else if (event.key === 'ArrowRight') {
navigateImage('next');
} else if (event.key === 'ArrowLeft') {
navigateImage('prev');
}
});

function closeOverlay() {
const overlay = document.getElementById('zoomoverlay');
overlay.classList.remove('show');

setTimeout(() => {
overlay.style.display = 'none';
}, 300);
}
});