English
Español
Français
Português
BTC
ETH
LTC
BCH
USDT
DOGE
DASH
USDC
XRP
XMR
TRX
BNB
SHIB
SOL
DAI
ZEC
ETC
POL
ADA
XLM
Mainboard
$386.33
₿ 0.00576
Principales caractéristiques
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the housing
- Step 6
- Remove the 2 screws, take off the metal bar, and disconnect the main FPC cable
Caractéristiques
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the housing
- Step 6
- Remove the 2 screws, take off the metal bar, and disconnect the main FPC cable
- Step 7
- Remove the bottom daughterboard
- Step 8
- Remove the 3 cameras
- Step 9
- Disconnect the volume buttons, power button, and front camera
- Step 10
- Completely loosen the motherboard screws and carefully flip it over
- Step 11
- Remove the short antenna cable from the motherboard
- Step 12
- Remove the long antenna cable from the motherboard
- Step 13
- Remove the short motherboard signal cable
- Step 14
- Remove the long motherboard signal cable
- Step 15
- Install the short motherboard signal cable
- Step 16
- Install the long motherboard signal cable
- Step 17
- Install the long antenna cable
- Step 18
- Flip the motherboard back over and reinstall it
- Step 19
- Reconnect the volume buttons, power button, and front camera
- Step 20
- Reattach the main camera and wide-angle camera
- Step 21
- Reattach the bottom daughterboard and reconnect the cable
- Step 22
- Reinstall the metal bar and secure everything again
- Step 23
- Place the screen display back into the housing
- Step 24
- Reinsert the battery
- Step 25
- Reattach the battery cover
Description
Watch the tutorial on YouTube
Replacement Instructions
5 min
Very easy
Required:
A soft surface
– You can use a towel, for example
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opener on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle under the battery.
Then make a 45-degree movement with the opener and lift the battery up.
Carefully loosen all 8 screws.
Use the correct screwdriver to avoid damage.
Set the screws aside so you do not lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners on the bottom side.
Apply just enough force to loosen them.
Use a spudger to carefully loosen the screen.
Work along the edges to release the clips.
Do not remove the screen before everything has been disconnected first.
Remove the 2 screws.
Take off the metal bar after you have loosened the screws.
Disconnect the main PFC cable from the housing.
Unscrew the board’s fasteners.
Carefully lift the board up.
Gently disconnect the cables.
First, use the spudger to disconnect the front camera.
Then remove the main camera and wide-angle camera with the spudger.
Set the main and wide-angle cameras aside completely for now.
Disconnect the volume buttons on the left side with the spudger. Apply some force.
Do the same with the power button on the right side. Apply some force.
Fully disconnect the front camera and set it aside.
Loosen all screws from the motherboard.
Then carefully flip the motherboard over using the spudger.
Make sure all cables remain intact and are not damaged.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the short antenna cable from the motherboard.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the long antenna cable from the motherboard.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the short motherboard signal cable from the motherboard.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the long motherboard signal cable from the motherboard.
Locate where you need to place the short motherboard signal cable.
Carefully press it down with a finger and guide the cable to the other point.
Press the other end of the motherboard signal cable into place as well.
Locate where you need to place the long motherboard signal cable.
Carefully press it down with a finger and guide the cable to the other point.
Press the other end of the motherboard signal cable into place as well.
Locate where you need to place the long motherboard signal cable.
Carefully press it down with a finger and guide the cable to the other point.
Press the other end of the motherboard signal cable into place as well.
Carefully flip the motherboard over and place it back in the correct position.
Make sure no cables are trapped underneath the motherboard.
Then screw the motherboard back into place.
Reconnect the volume buttons properly.
Reconnect the power button.
Put the front camera back in place.
Click the main camera back into the correct position.
Click the wide-angle camera back into the correct position.
Make sure the main camera is positioned above the wide-angle camera.
Reconnect the cable on the left side to the bottom daughterboard.
Flip the bottom daughterboard over and place it back in the correct position.
Screw the bottom daughterboard back into place.
Put the main FPC cable back in place.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the housing.
Press the screen firmly along the edges.
Check that the screen is securely attached everywhere.
Put the SHIFTphone battery back in.
Place it correctly in the SHIFTphone.
With the SHIFT logo facing up and the + and – in the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back onto the SHIFTphone in the correct position.
Press at 8 points to make sure the battery cover is securely attached.
Replacement Instructions
5 min
Very easy
Required:
A soft surface
– You can use a towel, for example
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opener on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle under the battery.
Then make a 45-degree movement with the opener and lift the battery up.
Carefully loosen all 8 screws.
Use the correct screwdriver to avoid damage.
Set the screws aside so you do not lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners on the bottom side.
Apply just enough force to loosen them.
Use a spudger to carefully loosen the screen.
Work along the edges to release the clips.
Do not remove the screen before everything has been disconnected first.
Remove the 2 screws.
Take off the metal bar after you have loosened the screws.
Disconnect the main PFC cable from the housing.
Unscrew the board’s fasteners.
Carefully lift the board up.
Gently disconnect the cables.
First, use the spudger to disconnect the front camera.
Then remove the main camera and wide-angle camera with the spudger.
Set the main and wide-angle cameras aside completely for now.
Disconnect the volume buttons on the left side with the spudger. Apply some force.
Do the same with the power button on the right side. Apply some force.
Fully disconnect the front camera and set it aside.
Loosen all screws from the motherboard.
Then carefully flip the motherboard over using the spudger.
Make sure all cables remain intact and are not damaged.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the short antenna cable from the motherboard.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the long antenna cable from the motherboard.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the short motherboard signal cable from the motherboard.
First, use the spudger to disconnect the connector.
Apply light force, but not too much.
Then fully disconnect the long motherboard signal cable from the motherboard.
Locate where you need to place the short motherboard signal cable.
Carefully press it down with a finger and guide the cable to the other point.
Press the other end of the motherboard signal cable into place as well.
Locate where you need to place the long motherboard signal cable.
Carefully press it down with a finger and guide the cable to the other point.
Press the other end of the motherboard signal cable into place as well.
Locate where you need to place the long motherboard signal cable.
Carefully press it down with a finger and guide the cable to the other point.
Press the other end of the motherboard signal cable into place as well.
Carefully flip the motherboard over and place it back in the correct position.
Make sure no cables are trapped underneath the motherboard.
Then screw the motherboard back into place.
Reconnect the volume buttons properly.
Reconnect the power button.
Put the front camera back in place.
Click the main camera back into the correct position.
Click the wide-angle camera back into the correct position.
Make sure the main camera is positioned above the wide-angle camera.
Reconnect the cable on the left side to the bottom daughterboard.
Flip the bottom daughterboard over and place it back in the correct position.
Screw the bottom daughterboard back into place.
Put the main FPC cable back in place.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the housing.
Press the screen firmly along the edges.
Check that the screen is securely attached everywhere.
Put the SHIFTphone battery back in.
Place it correctly in the SHIFTphone.
With the SHIFT logo facing up and the + and – in the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back onto the SHIFTphone in the correct position.
Press at 8 points to make sure the battery cover is securely attached.
Autres produits de NovaCustom
Tous les produits
$386.33
₿ 0.00576
