English
Español
Français
Português
BTC
ETH
LTC
BCH
USDT
DOGE
DASH
USDC
XRP
XMR
TRX
BNB
SHIB
SOL
DAI
ZEC
ETC
POL
ADA
XLM
Long motherboard signal cable
$5.52
₿ 0.00008
Especificaciones principales
- Step 1
- Remove the Battery Cover
- Step 2
- Remove the Battery
- Step 3
- Remove the 8 Screws
- Step 4
- Remove the Screws at the Bottom of the SHIFTphone
- Step 5
- Use the Spudger to Remove the Screen Display from the Case
- Step 6
- Unscrew the 2 Screws, Remove the Metal Bar, and Unclip the Main FPC Cable
Especificaciones
- Step 1
- Remove the Battery Cover
- Step 2
- Remove the Battery
- Step 3
- Remove the 8 Screws
- Step 4
- Remove the Screws at the Bottom of the SHIFTphone
- Step 5
- Use the Spudger to Remove the Screen Display from the Case
- Step 6
- Unscrew the 2 Screws, Remove the Metal Bar, and Unclip the Main FPC Cable
- Step 7
- Remove the Bottom Daughterboard
- Step 8
- Remove the Long Antenna Cable
- Step 9
- Install the New Long Antenna Cable, Also Secure to the Bottom Daughterboard
- Step 10
- Reinstall the Bottom Daughterboard
- Step 11
- Reinsert the Metal Bar and Reattach Everything
- Step 12
- Reinstall the Screen Display onto the Case
- Step 13
- Reinsert the Battery
- Step 14
- Reattach the Battery Cover
Descripción
Watch the tutorial on YouTube
Replacement Instructions
5 min
Very Easy
Required Tools:
A soft surface
– For example, you can use a towel
Spudger
Micro-screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then, remove the battery cover using the opener at the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and position one end in the middle underneath the battery.
Then make a 45-degree movement with the opener and lift the battery up.
Carefully unscrew all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Apply just enough force to unscrew them.
Use a spudger to carefully detach the screen.
Run it along the edges to unclip the clips.
Do not detach the screen without first loosening everything.
Unscrew the 2 screws.
Remove the metal bar after you’ve unscrewed the screws.
Unclip the main FPC cable from the case.
Unscrew the fasteners of the board.
Carefully lift the board up.
Gently disconnect the cables.
Check where the antenna cable is secured and how it is routed within the device.
Gently detach the antenna cable from the connectors.
Carefully pull the cable out of its routing without damaging it.
Route the new antenna cable in the same path as the old cable.
Firmly connect the cable to the appropriate connectors.
Attach it to the bottom daughterboard and ensure everything is secured properly.
Place the board back in its position.
Reconnect all cables.
Secure the board tightly with screws.
Reinsert the main FPC cable.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the case.
Press the screen firmly along the edges.
Check that the screen is securely attached all around.
Place the battery back into the SHIFTphone.
Install it correctly into the SHIFTphone.
The SHIFT logo should be facing up, with the + and – at the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone correctly.
Press down at 8 points to ensure the battery cover is securely attached.
Replacement Instructions
5 min
Very Easy
Required Tools:
A soft surface
– For example, you can use a towel
Spudger
Micro-screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then, remove the battery cover using the opener at the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and position one end in the middle underneath the battery.
Then make a 45-degree movement with the opener and lift the battery up.
Carefully unscrew all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Apply just enough force to unscrew them.
Use a spudger to carefully detach the screen.
Run it along the edges to unclip the clips.
Do not detach the screen without first loosening everything.
Unscrew the 2 screws.
Remove the metal bar after you’ve unscrewed the screws.
Unclip the main FPC cable from the case.
Unscrew the fasteners of the board.
Carefully lift the board up.
Gently disconnect the cables.
Check where the antenna cable is secured and how it is routed within the device.
Gently detach the antenna cable from the connectors.
Carefully pull the cable out of its routing without damaging it.
Route the new antenna cable in the same path as the old cable.
Firmly connect the cable to the appropriate connectors.
Attach it to the bottom daughterboard and ensure everything is secured properly.
Place the board back in its position.
Reconnect all cables.
Secure the board tightly with screws.
Reinsert the main FPC cable.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the case.
Press the screen firmly along the edges.
Check that the screen is securely attached all around.
Place the battery back into the SHIFTphone.
Install it correctly into the SHIFTphone.
The SHIFT logo should be facing up, with the + and – at the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone correctly.
Press down at 8 points to ensure the battery cover is securely attached.
Más productos de NovaCustom
Todos los productos
$5.52
₿ 0.00008
