English
Español
Français
Português
BTC
ETH
LTC
BCH
USDT
DOGE
DASH
USDC
XRP
XMR
TRX
BNB
SHIB
SOL
DAI
ZEC
ETC
POL
ADA
XLM
Ear speaker
$43.05
₿ 0.00064
Principales caractéristiques
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the housing
- Step 6
- Remove the 2 screws, take off the metal bar, and disconnect the main FPC cable
Caractéristiques
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the housing
- Step 6
- Remove the 2 screws, take off the metal bar, and disconnect the main FPC cable
- Step 7
- Remove the bottom daughterboard
- Step 8
- Remove the earpiece speaker and the inner bottom frame
- Step 9
- Place the new inner bottom frame and put the earpiece speaker back
- Step 10
- Reinstall the bottom daughterboard
- Step 11
- Put the metal bar back and reattach everything
- Step 12
- Place the screen display back onto the housing
- Step 13
- Reinsert the battery
- Step 14
- Reattach the battery cover
Description
Replacement Instructions
5 min
Very easy
Required:
A soft surface
– For example, you can use a towel
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opener on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle under the battery.
Then make a 45-degree movement with the opener and lift the battery upward.
Carefully loosen all 8 screws.
Use a suitable screwdriver to avoid damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners on the bottom side.
Apply just enough force to loosen them.
Use a spudger to carefully detach the screen.
Work along the edges to release the clips.
Do not remove the screen before everything has been disconnected first.
Remove the 2 screws.
Take off the metal bar after loosening the screws.
Disconnect the main FPC cable from the housing.
Unscrew the board fasteners.
Carefully lift the board up.
Turn the board over and place it temporarily on the top side of the SHIFTphone.
Use the opening tool to remove the earpiece speaker from the inner bottom frame.
Do this by moving it at a 90-degree angle.
Then use the same opening tool to remove the inner bottom frame.
Put the new inner bottom frame back in place.
Make sure everything is positioned correctly.
Place the earpiece speaker back in the correct position in the inner bottom frame.
Put the bottom daughterboard back in place.
Make sure it is seated correctly.
Tighten the board securely with screws.
Put the main FPC cable back in place.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the housing.
Press the screen firmly along the edges.
Check that the screen is securely attached all around.
Put the SHIFTphone battery back in place.
Insert it correctly into the SHIFTphone.
With the SHIFT logo facing up and the + and – in the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone the correct way.
Press down at 8 points until the battery cover is securely in place.
5 min
Very easy
Required:
A soft surface
– For example, you can use a towel
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opener on the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle under the battery.
Then make a 45-degree movement with the opener and lift the battery upward.
Carefully loosen all 8 screws.
Use a suitable screwdriver to avoid damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners on the bottom side.
Apply just enough force to loosen them.
Use a spudger to carefully detach the screen.
Work along the edges to release the clips.
Do not remove the screen before everything has been disconnected first.
Remove the 2 screws.
Take off the metal bar after loosening the screws.
Disconnect the main FPC cable from the housing.
Unscrew the board fasteners.
Carefully lift the board up.
Turn the board over and place it temporarily on the top side of the SHIFTphone.
Use the opening tool to remove the earpiece speaker from the inner bottom frame.
Do this by moving it at a 90-degree angle.
Then use the same opening tool to remove the inner bottom frame.
Put the new inner bottom frame back in place.
Make sure everything is positioned correctly.
Place the earpiece speaker back in the correct position in the inner bottom frame.
Put the bottom daughterboard back in place.
Make sure it is seated correctly.
Tighten the board securely with screws.
Put the main FPC cable back in place.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the housing.
Press the screen firmly along the edges.
Check that the screen is securely attached all around.
Put the SHIFTphone battery back in place.
Insert it correctly into the SHIFTphone.
With the SHIFT logo facing up and the + and – in the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone the correct way.
Press down at 8 points until the battery cover is securely in place.
Autres produits de NovaCustom
Tous les produits
$43.05
₿ 0.00064
