English
Español
Français
Português
BTC
ETH
LTC
BCH
USDT
DOGE
DASH
USDC
XRP
XMR
TRX
BNB
SHIB
SOL
DAI
ZEC
ETC
POL
ADA
XLM
Usb-C port
$43.05
₿ 0.00064
Principais especificações
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to detach the screen display from the case
- Step 6
- Unscrew the 2 screws, remove the metal bar, and disconnect the main FPC cable
Especificações
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to detach the screen display from the case
- Step 6
- Unscrew the 2 screws, remove the metal bar, and disconnect the main FPC cable
- Step 7
- Remove the bottom daughterboard
- Step 8
- Remove the USB-C module
- Step 9
- Install the new USB-C module
- Step 10
- Reinstall the bottom daughterboard
- Step 11
- Reattach the metal bar and secure everything
- Step 12
- Reinstall the screen display on the casing
- Step 13
- Reinsert the battery
- Step 14
- Reattach the battery cover
Descrição
Watch the tutorial on YouTube
Replacement Instructions
5 min
Very easy
Requirements:
A soft surface
– You can use a towel, for example
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opener at the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle below the battery.
Then make a 45-degree motion with the opener and lift the battery up.
Carefully unscrew all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Use just enough force to unscrew them.
Use a spudger to gently pry the screen loose.
Run along the edges to disengage the clips.
Do not detach the screen without first loosening everything.
Unscrew the 2 screws.
Remove the metal bar after unscrewing the screws.
Disconnect the main FPC cable from the case.
Unscrew the fasteners of the board.
Carefully lift the board up.
Gently disconnect the cables.
Locate the USB-C module on the board.
Gently disconnect the connector.
Remove the module from the casing.
Place the new module in the correct position.
Firmly connect the connector.
Ensure everything is securely attached.
Put the board back in its place.
Reconnect all cables.
Screw the board securely in place.
Reconnect the main FPC cable.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the casing.
Press the screen firmly along the edges.
Check that the screen is securely attached all around.
Place the battery back into the SHIFTphone.
Insert it correctly into the SHIFTphone.
With the SHIFT logo facing up and the + and – on the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone correctly.
Press firmly at 8 points to ensure the battery cover is secure.
>
Replacement Instructions
5 min
Very easy
Requirements:
A soft surface
– You can use a towel, for example
Spudger
Micro screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then remove the battery cover using the opener at the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle below the battery.
Then make a 45-degree motion with the opener and lift the battery up.
Carefully unscrew all 8 screws.
Use a suitable screwdriver to prevent damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Use just enough force to unscrew them.
Use a spudger to gently pry the screen loose.
Run along the edges to disengage the clips.
Do not detach the screen without first loosening everything.
Unscrew the 2 screws.
Remove the metal bar after unscrewing the screws.
Disconnect the main FPC cable from the case.
Unscrew the fasteners of the board.
Carefully lift the board up.
Gently disconnect the cables.
Locate the USB-C module on the board.
Gently disconnect the connector.
Remove the module from the casing.
Place the new module in the correct position.
Firmly connect the connector.
Ensure everything is securely attached.
Put the board back in its place.
Reconnect all cables.
Screw the board securely in place.
Reconnect the main FPC cable.
Place the metal bar back in the correct position.
Tighten the two screws again.
Carefully place the screen display back onto the casing.
Press the screen firmly along the edges.
Check that the screen is securely attached all around.
Place the battery back into the SHIFTphone.
Insert it correctly into the SHIFTphone.
With the SHIFT logo facing up and the + and – on the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and place it back on the SHIFTphone correctly.
Press firmly at 8 points to ensure the battery cover is secure.
>
Mais produtos de NovaCustom
Todos os produtos
$43.05
₿ 0.00064
