English
Español
Français
Português
BTC
ETH
LTC
BCH
USDT
DOGE
DASH
USDC
XRP
XMR
TRX
BNB
SHIB
SOL
DAI
ZEC
ETC
POL
ADA
XLM
Short motherboard signal cable
$5.52
₿ 0.00008
Principais especificações
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the case
- Step 6
- Unscrew the 2 screws, remove the metal bar, and disconnect the main FPC cable
Especificações
- Step 1
- Remove the battery cover
- Step 2
- Remove the battery
- Step 3
- Remove the 8 screws
- Step 4
- Remove the screws at the bottom of the SHIFTphone
- Step 5
- Use the spudger to remove the screen display from the case
- Step 6
- Unscrew the 2 screws, remove the metal bar, and disconnect the main FPC cable
- Step 7
- Remove the bottom daughterboard
- Step 8
- Remove the short motherboard signal cable
- Step 9
- Place the new short motherboard signal cable
- Step 10
- Reinstall the bottom daughterboard
- Step 11
- Reattach the metal bar and secure everything
- Step 12
- Reinstall the screen display onto the case
- Step 13
- Reinsert the battery
- Step 14
- Reattach the battery cover
Descrição
Watch the tutorial on YouTube
Replacement Instructions
5 min
Very Easy
Requirements:
A soft surface
– You can use a towel, for example
Spudger
Micro-screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then, remove the battery cover using the opener at the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle under the battery.
Then, make a 45-degree motion with the opener and lift the battery up.
Carefully unscrew all 8 screws.
Use a suitable screwdriver to avoid damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Apply just enough force to loosen them.
Use a spudger to gently pry the screen loose.
Go along the edges to release the clips.
Do not detach the screen without first loosening everything.
Unscrew the 2 screws.
Remove the metal bar after unscrewing the screws.
Disconnect the main FPC cable from the case.
Unscrew the fasteners of the board.
Gently lift the board upwards.
Carefully disconnect the cables.
Locate the short motherboard signal cable on the motherboard.
Gently disconnect the connector without using force.
Completely remove the cable from the device.
Take the new short motherboard signal cable and check the connection.
Place the connector correctly onto the motherboard.
Gently press the cable until it is securely connected.
Put the board back into place.
Reconnect all cables.
Screw the board securely back in.
Reinsert the main FPC cable.
Place the metal bar back in the correct position.
Screw the two screws back in securely.
Carefully place the screen display back onto the case.
Press the screen firmly along the edges.
Check to ensure that the screen is securely in place all around.
Place the battery back into the SHIFTphone.
Ensure it is positioned correctly in the SHIFTphone.
With the SHIFT logo facing up, and the + and – symbols at the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and position it correctly on the SHIFTphone.
Press firmly at 8 points to ensure the battery cover is secured.
Replacement Instructions
5 min
Very Easy
Requirements:
A soft surface
– You can use a towel, for example
Spudger
Micro-screwdriver
Place the SHIFTphone upside down on a soft surface.
This prevents scratches on the SHIFTphone.
Then, remove the battery cover using the opener at the side of the battery cover.
Place the SHIFTphone with the camera facing up on a soft surface.
Take the opener and place one end in the middle under the battery.
Then, make a 45-degree motion with the opener and lift the battery up.
Carefully unscrew all 8 screws.
Use a suitable screwdriver to avoid damage.
Set the screws aside so you don’t lose them.
Hold the SHIFTphone firmly on both sides.
Unscrew the fasteners at the bottom.
Apply just enough force to loosen them.
Use a spudger to gently pry the screen loose.
Go along the edges to release the clips.
Do not detach the screen without first loosening everything.
Unscrew the 2 screws.
Remove the metal bar after unscrewing the screws.
Disconnect the main FPC cable from the case.
Unscrew the fasteners of the board.
Gently lift the board upwards.
Carefully disconnect the cables.
Locate the short motherboard signal cable on the motherboard.
Gently disconnect the connector without using force.
Completely remove the cable from the device.
Take the new short motherboard signal cable and check the connection.
Place the connector correctly onto the motherboard.
Gently press the cable until it is securely connected.
Put the board back into place.
Reconnect all cables.
Screw the board securely back in.
Reinsert the main FPC cable.
Place the metal bar back in the correct position.
Screw the two screws back in securely.
Carefully place the screen display back onto the case.
Press the screen firmly along the edges.
Check to ensure that the screen is securely in place all around.
Place the battery back into the SHIFTphone.
Ensure it is positioned correctly in the SHIFTphone.
With the SHIFT logo facing up, and the + and – symbols at the top left.
Place the SHIFTphone upside down again on a soft surface.
Take the battery cover and position it correctly on the SHIFTphone.
Press firmly at 8 points to ensure the battery cover is secured.
Mais produtos de NovaCustom
Todos os produtos
$5.52
₿ 0.00008
