Aune Audio N7 Headphone Amplifier

The Aune N7 is a fully discrete Class A / Class AB headphone amplifier that puts up to 6.5 watts of balanced output into a chassis just over eight inches wide. It uses design ideas from Aune's larger amplifiers, including a twin JFET input stage, R2R volume control, and two bias current settings, in a size that fits a crowded desk.

The N7 is a pure analog amplifier and preamp with no DAC inside. Feed it from any DAC or streamer over RCA or balanced XLR, and it handles everything after the conversion. It is a good first serious amplifier for listeners stepping up from a dongle or an all-in-one DAC/amp.

Class A and Class AB Operation

Aune describes the N7 as a Class A / Class AB amplifier. At low output, its transistors run in Class A, carrying current all the time, which avoids crossover distortion, a small error that can occur when transistors hand the signal back and forth. As output rises, the N7 moves into Class AB, which runs cooler and makes its full 6.5 watts possible.

Aune publishes where that change happens. From the balanced output, the N7 stays in Class A up to 57.2mW into 32 ohms and up to 540mW into 300 ohms, and runs in Class AB above those levels. In-ear monitors and efficient headphones at normal volume sit inside that range, while demanding planar headphones will push it into Class AB.

Our reviewer Cameron Oatley (GoldenSound) measured the N7's power draw at the wall and found the behavior of a high-bias Class AB design. He still called it his go-to amp under $500 and an easy default recommendation for high-end desktop performance at this price.

Twin JFET Input

JFETs have high input impedance and a smooth, tube-like sound, without a tube's fragility or maintenance. The N7 uses a matched pair of twin JFETs packaged together, so both devices heat up evenly and keep the circuit's midpoint voltage stable. That keeps the sound consistent from the moment you turn it on through a long listening session.

Bias Current and Gain Settings

The N7 has two bias current settings. A-L runs more efficiently and gives a tighter, more focused sound, and A-H gives a fuller presentation with more body and richness. The display shows the active setting in blue or red along with the internal temperature. Two gain settings then match the output to the headphone, from sensitive in-ear monitors on low gain to demanding full-size headphones on high.

Aune measures the noise floor at 3 microvolts in high gain and THD+N below 0.0004% at 1kHz, so in-ear monitors play against a quiet background. Harder-to-drive headphones get up to 6,570mW into 32 ohms or 750mW into 300 ohms from the balanced output. The full aluminum chassis has heatsink fins along its sides to keep temperatures stable.

R2R Volume Control

The N7 uses two JRC R2R electronic volume chips with dedicated op-amps, forming a four-channel balanced volume chain. A conventional potentiometer can lose left-right balance at the bottom of its range. This control stays matched at low volume, which matters for late-night listening, and it keeps imaging and soundstage intact.

One multifunctional knob handles volume, input, bias current, gain, and headphone or preamp switching, and the 3-inch display is easy to read from across the desk. An aluminum remote is included for adjusting volume from the couch.

Preamp Outputs

The N7 has two headphone outputs (6.35mm single-ended and 4.4mm balanced), two line inputs (RCA and XLR), and two preamp outputs (RCA and XLR), with an independent preamp mode. Connect powered monitors or a power amplifier, and the N7 becomes the control center of a compact desktop system for both headphones and speakers.

Power comes from an external 18V adapter, which keeps AC conversion outside the chassis. Component selection follows Aune's desktop line: Panasonic electrolytic capacitors, WIMA decoupling capacitors, and a communication-grade PCB.

How the N7 Compares

The natural reference point is Aune's own S17 Pro EVO, which shares the twin JFET input, R2R volume, and selectable bias current. The S17 Pro EVO adds a 50W internal toroidal supply, a 4-pin XLR output, 7.5 watts of balanced power, and a much wider Class A range: 2.07 watts into 32 ohms against the N7's 57.2mW. The N7 costs half as much, and 6.5 watts balanced is more power than most amplifiers near $399 offer. Run your own headphones through our headphone power calculator to see how much you need.

Aune's own photos pair the N7 with its AR5000 open-back, and the two make a warm, spacious desktop system for well under a thousand dollars. The N7 works just as well with any DAC you already own.

Key Features


Fully discrete Class A / Class AB headphone amplifier and preamp
Up to 6.5W balanced output (6,570mW into 32 ohms, high gain)
Class A up to 57.2mW into 32 ohms and 540mW into 300 ohms (balanced); Class AB above
Matched twin JFET input stage for a smooth, tube-like character
Two bias current settings (A-L / A-H) with two-color display
Two gain settings covering sensitive IEMs to full-size headphones
3uV output noise floor in high gain; THD+N below 0.0004% at 1kHz
Four-channel balanced R2R volume control with dual JRC chips
6.35mm single-ended and 4.4mm balanced headphone outputs
RCA and XLR line inputs; RCA and XLR preamp outputs
Independent preamp function for powered speakers
3-inch display with real-time temperature readout
Multifunctional knob and aluminum remote control
Full aluminum chassis with integrated heatsink fins
Panasonic and WIMA components on a communication-grade PCB
Hi-Res Audio certification


Technical Specs




Product Type
Class A / Class AB headphone amplifier and preamplifier


Architecture
Fully discrete


Class A Operating Range
Balanced: up to 57.2mW at 32 ohms, up to 540mW at 300 ohms; Class AB above these levels


Input Stage
Matched twin JFET


Bias Current Settings
A-L (low) / A-H (high), selectable


Gain Settings
Low / High


Volume Control
Four-channel balanced R2R, dual JRC chips with dedicated op-amps


Headphone Outputs
6.35mm single-ended, 4.4mm balanced


Line Inputs
RCA (10K ohm) and XLR (22K ohm)


Preamp Outputs
RCA (200 ohm) and XLR (100 ohm)


Headphone Output Impedance
1 ohm


Frequency Response
20Hz - 80kHz, +/-0.05dB


THD+N
<0.0004% at 1kHz


Output Noise
3uV (high gain)


SNR
>105dB at 600 ohms


Crosstalk
< -100dB at 1kHz, 600 ohms


Power
External 18V DC adapter


Display
3-inch display with temperature readout


Dimensions
208 x 160 x 83mm


Remote
Aluminum remote control included




Headphone Output Power (High Gain)




Load
Single-Ended Output
Balanced Output




32 ohms
1,900mW
6,570mW


100 ohms
616mW
2,190mW


150 ohms
416mW
1,500mW


250 ohms
252mW
900mW


300 ohms
213mW
750mW


470 ohms
136mW
480mW


600 ohms
106mW
370mW




What's in the Box


Aune N7 headphone amplifier
Power adapter and power cord
6.35mm to 3.5mm adapter
Quick start guide